0800 215 104
[email protected]
16/10 Olive Road, Penrose, Auckland 1061
Account
$0.00 0

Cart

Free Shipping on purchases above $2500. NZ only.

No products in the cart.

Continue shopping

PTFE vs Other Diaphragm Pump Materials: Which One Belongs in Your Pump?

GRACO PTFE Diaphragm Pump Kits

Reordering a diaphragm usually comes down to one line on the form: PTFE, Santoprene, Hytrel, Buna-N, etc. Get it wrong, and a diaphragm pump that should run for months or years can split the diaphragm in weeks, or worse, an incorrect elastomer can swell or fail the first time it meets a solvent.

As an official Graco distributor in New Zealand, we answer this question often. Here’s how the materials compare, when a PTFE diaphragm pump is worth the extra cost, and a chemical chart to check before you reorder.

Why Diaphragm Material Decides How Long Your Pump Lasts

In AODD pumps (air-operated double diaphragm pumps), the diaphragm flexes on every stroke. It’s also the only barrier between your process fluid and the pump’s air side motor.

When the diaphragm material doesn’t suit the fluid, it can swell, harden, or crack. Fluid can then enter the air side, contaminate product, and stop production without warning. The diaphragm is one of the cheapest parts in the pump, but it often decides how much downtime you’ll have.

Where a PTFE Diaphragm Pump Earns Its Place (and Where It Doesn’t)

PTFE (polytetrafluoroethylene) is the go-to material for aggressive fluids. Graco rates it as the most chemically compatible diaphragm material it offers, with extreme corrosion resistance and a low-friction, non-stick surface. If you’re moving concentrated acids, solvents, or strong caustics, the conversation usually starts with a PTFE diaphragm pump.

But PTFE has trade-offs. It isn’t an elastomer, so it’s stiffer than rubber and less forgiving of constant flexing. That’s why standard PTFE diaphragms run with a backer diaphragm behind them.

Two-Piece vs Overmoulded PTFE

A two-piece PTFE diaphragm pairs a PTFE face with a separate backer. Graco’s overmoulded PTFE bonds an FDA-compliant PTFE face and an EPDM air side into one part, with no exposed diaphragm plate on the fluid side. Graco reports up to three times longer diaphragm life with overmoulded PTFE on its ½” to 3″ pumps compared with standard diaphragms.

Its maximum temperature is lower at 82°C, although it handles colder conditions down to -10°C. Check your process temperature before you switch. For sites pumping slurries or pigmented fluids that still need PTFE, fewer change-outs mean less downtime and lower labour costs across the year.

PTFE vs Santoprene, Hytrel, and Other Diaphragm Materials

Here’s how PTFE compares with other diaphragm materials in Graco’s range. These temperature limits are based on mechanical stress only, so some chemicals will narrow them further.

Graco Diaphragm Materials Compared:

MaterialTemperature RangeStrengthsWatch Out For
PTFE4°C to 100°CWidest chemical compatibility, non-stickPoor abrasion resistance, needs a backer
Overmoulded PTFE-10°C to 82°CPTFE chemistry with longer life in abrasive dutyLower maximum temperature
Santoprene-40°C to 82°CAbrasion and chemical resistance; caustics, dilute acids, alcohols, some solventsConcentrated chemicals usually need PTFE; petroleum oils
TPE (Hytrel)-29°C to 66°CLow-temperature performance, abrasion resistanceLowest top temperature in the range
G.E.T. (Graco Engineered Thermoplastic)-40°C to 82°CAbrasion resistance, similar chemistry to Buna-NStrong solvents
Buna-N (nitrile)-12°C to 82°CPetroleum fluids, oils, waterAcetone, MEK, chlorinated solvents
EPDM-51°C to 135°CHigh heat, steam, caustics, CIP sanitisersPetroleum oils
FKM (Viton)-40°C to 160°CHigh heat, acids, fuelsKetones, low molecular weight esters

Graco’s own popular configurations pair TPE with *petroleum products on aluminium pumps and Santoprene with diluted chemicals on polypropylene pumps. PTFE takes over once the chemicals get concentrated.

*Unleaded Fuel

PTFE Chemical Compatibility Chart for Common NZ Process Fluids

Most PTFE chemical compatibility chart pages online come from lab suppliers and rate a static sample soaked for 48 hours. A diaphragm flexes thousands of times a shift, so use the PTFE chemical resistance chart below as a starting point. Then confirm against Graco’s Chemical Compatibility Guide for your exact concentration and temperature.

Fluid (Typical NZ Use)PTFESantopreneBuna-NEPDM
Caustic soda (dairy CIP)✓✓~✓
Dilute acids✓✓~✓
Concentrated acids✓~✗~
Sodium hypochlorite (wastewater dosing)✓~✗~
Peracetic acid sanitiser, e.g. Oxonia (food CIP)✓~✗~
Ketones such as MEK and acetone (coatings)✓~✗✓
Diesel, oils, and petroleum fluids✓✗✓✗
  • ✓ – Generally suitable
  • ~ – Depends on concentration and temperature
  • ✗ – Avoid

This is for general guidance only. Confirm with Graco’s Chemical Compatibility Guide or our team before ordering.

One more thing. A PTFE diaphragm won’t protect an incompatible ball, seat, or O-ring. Graco’s rule is to stay within the limits of the most restricted wetted part, so check the whole pump. PTFE itself is attacked by only a handful of chemicals, such as molten alkali metals like sodium and fluorinating agents.

PFA vs PTFE Chemical Resistance: Does It Matter for Pumps?

If you’ve searched for a PFA vs PTFE chemical resistance chart, here’s the short answer: chemically, they’re almost identical. Both are fluoropolymers rated as inert to nearly all industrial chemicals.

The difference is in how they’re made and how they flex. PFA can be melt-processed, which suits moulded linings, fittings, and tubing. PTFE handles repeated folding better, and that’s exactly what a diaphragm does all day. So your pump runs a PTFE diaphragm, while PFA is more likely to turn up in lined pipework.

PropertyPTFEPFA
Chemical resistanceInertInert
Melt-processableNoYes
Diaphragm flexingBetter suited to continuous flexingGood, but rarely used for diaphragms
Heat resistanceSlightly higherSlightly lower
Typical pump-system useDiaphragms, check ballsLinings, fittings, tubing

Matching Diaphragm Material to Your Industry

  • Food and Dairy: HACCP plans depend on cleaning that doesn’t damage your equipment. EPDM is commonly specified for CIP sanitisers, but peracetic acid products like Oxonia can be hard on elastomers at higher concentrations, so check Graco’s guide to determine your dosing rate. Overmoulded PTFE is also available for Graco’s sanitary pumps. Always confirm food-contact certification for the exact part number.
  • Chemical Processing: PTFE or overmoulded PTFE handles concentrates. Santoprene often covers diluted chemicals at a lower cost per diaphragm.
  • Wastewater: Grit and solids favour abrasion-resistant materials like G.E.T. or Santoprene. Hypochlorite dosing points back to PTFE.

Eliminate Unplanned Downtime with Genuine Diaphragms

Swelling, cracking around the bolt holes, or fluid in the air exhaust all signal that the material isn’t right for your duty. A cheaper look-alike rarely fixes it. Our guide to genuine Graco parts explains why non-genuine diaphragms end up costing more.

Our in-house team can review your fluid, build a preventive maintenance plan around it, and keep the right diaphragm kits on hand. Ask us about our current stock of Graco diaphragm kits when you need a replacement.

FAQs

Is PTFE better than Santoprene for a diaphragm pump?

For concentrated or aggressive chemicals, yes. For diluted chemicals, water, and abrasive fluids, Santoprene often lasts longer and costs less.

What temperature can a PTFE diaphragm handle?

Graco rates standard PTFE from 4°C to 100°C and overmoulded PTFE from -10°C to 82°C, before any chemical limits apply.

Can I swap diaphragm material without changing the rest of the pump?

Often, yes, if a kit exists for your model. Check the balls, seats, and O-rings too, since they need to suit the fluid as well.

Get the Right Diaphragm the First Time

Send us your fluid, temperature, and pump model, and we’ll confirm the right diaphragm and dispatch genuine Graco parts. Specifying a whole new pump instead? Compare AODD vs EODD pumps first, as Graco’s electric diaphragm pumps can cut energy costs by up to 80% compared with air-operated models.

With a passion for solutions, we at PumpWorks get our satisfaction from working with our clients. Pumpworks custom design, custom build and deliver!

Supplying brands and products for the Chemical and Pharmaceutical, Food and Wine, Oil and Gas, Water and Wastewater industries, we understand what is required and what works.
  • © Copyright - PumpWorks
  • 2026
  • All Rights Reserved

SEO By numero logo

Payment Method

How can we help?